Anodizing is the most specified surface treatment for CNC-machined aluminum, yet most drawings that arrive at KUSLA Prototype either call out the wrong type for the application or leave the type unspecified entirely. The result is parts that fail salt-spray testing, bores that bind after coating, or finishes that cost twice what the design requires. This guide breaks down the three anodizing types by the numbers that matter to engineers: oxide thickness, hardness, dimensional impact, alloy compatibility, cost, and the exact MIL-A-8625F callout format that prevents ambiguity at the finishing shop.
Key Takeaways
- Type II sulfuric anodizing is the default for most CNC aluminum parts: 5–25 μm thickness, 200–400 HV hardness, full color range, and the lowest cost of the three types.
- Type III hard anodize delivers 300–500+ HV at 25–75+ μm thickness, but costs 30–50% more and limits color options to black and dark tones.
- Type I chromic anodize is being phased out due to hexavalent chromium toxicity. Type IC (non-chromic alternatives) are replacing it in aerospace specifications.
- Anodizing grows the surface outward — Type II adds roughly one-third of the coating thickness per side; Type III adds roughly half. Machine bores and shafts undersized by that amount.
- Alloy choice determines finish quality. 6061 and 6063 anodize cleanly in any color. 7075 shifts brown. 2024 turns yellow-gray and limits coating thickness to 38 μm.
What Anodizing Actually Does to Aluminum — and Why the Type Matters
Anodizing is not a coating in the way paint or plating is a coating. It is an electrochemical conversion: the aluminum part is submerged in an acid electrolyte and connected as the anode (positive terminal) in an electrical circuit. Current flows, oxygen ions migrate to the surface, and the aluminum itself oxidizes into aluminum oxide (Al2O3) — a ceramic structure that is physically part of the base metal, not a separate layer sitting on top of it.
This distinction matters because the oxide grows both inward and outward from the original surface. The total coating thickness is split between penetration into the base metal and buildup above the original dimension. That split ratio changes with the anodizing type: Type II grows roughly one-third outward and two-thirds inward; Type III splits closer to 50/50. The practical consequence is that every anodized dimension changes, and the amount of change depends on which type the drawing specifies.
The type also determines the structure of the oxide. Type II produces a relatively porous, columnar oxide that absorbs dyes easily — which is why it supports the full spectrum of colors. Type III produces a denser, harder oxide formed at lower bath temperatures and higher current densities, which is why it resists abrasion but accepts only dark colors (black, dark bronze, dark gray). Type I produces the thinnest oxide of all, originally developed for aerospace fatigue-sensitive structures where minimal dimensional change and corrosion resistance matter more than wear or color.
Type I, II, and III: The Complete Specification Breakdown
The three types are defined by MIL-A-8625F, the military specification that governs anodic coatings on aluminum and aluminum alloys. Each type uses a different electrolyte, operates at different parameters, and produces an oxide with different properties. The table below consolidates the specifications that drive engineering decisions.
| Property | Type I (Chromic) | Type II (Sulfuric) | Type III (Hard Coat) |
|---|---|---|---|
| MIL-A-8625F Designation | Type I / IB / IC | Type II | Type III |
| Electrolyte | Chromic acid (Type I/IB); non-chromic alternative (Type IC) | Sulfuric acid, 15–20% | Sulfuric acid, low-temp formulation |
| Bath Temperature | ~38 °C (100 °F) | ~20 °C (68–72 °F) | −2 to 2 °C (28–36 °F) |
| Oxide Thickness | 0.5–7.6 μm | 5–25 μm (Class 1 ≥18 μm; Class 2 ≥10 μm) | 25–75+ μm (alloy dependent) |
| Surface Hardness | ~200 HV | 200–400 HV | 300–500+ HV |
| Dimensional Growth per Side | Negligible (<2.5 μm) | ~33% of coating thickness | ~50% of coating thickness |
| Color Options | Clear to gray only | Full range (clear, black, red, blue, gold, green, etc.) | Black, dark bronze, dark gray |
| Salt Spray (ASTM B117) | ≥336 hours | 1,000–3,000+ hours (sealed) | ≥336 hours (often higher) |
| Wear Resistance | Low | Moderate | High (Taber index ≤3.5 mg/1,000 cycles) |
| Max Operating Temp | ~65 °C | ~65–80 °C | ~80 °C (thermal crazing risk above) |
| Fatigue Impact | Minimal (<5% reduction) | 5–15% reduction | 15–30% reduction (alloy dependent) |
| Relative Cost | Highest (hazmat handling) | 1.0x (baseline) | 1.3–1.5x |
| Typical Applications | Aerospace fatigue-critical, legacy specs | Consumer electronics, medical devices, general CNC parts | Hydraulic cylinders, pistons, wear surfaces, military hardware |
Source: MIL-A-8625F, ASTM B580, AAC Anodizing Reference Guide. Class 1 = undyed; Class 2 = dyed.
Fig. 1 — Oxide layer thickness and growth direction for the three anodizing types. Type III’s 50/50 split means a 50 μm coating adds 25 μm per side to the finished dimension.
Which Aluminum Alloys Anodize Best — and Which Ones Fight the Process
The aluminum alloy determines the oxide quality, achievable thickness, color accuracy, and surface uniformity. Alloying elements — particularly copper, silicon, and zinc — interfere with oxide formation in predictable ways. KUSLA Prototype’s standard guidance: choose the alloy for its mechanical properties first, then verify that the required anodizing type and color are achievable on that alloy before finalizing the drawing.
| Alloy | Series / Key Element | Type II Quality | Type III Max Thickness | Color Behavior | Notes |
|---|---|---|---|---|---|
| 6061-T6 | 6xxx (Mg+Si) | Excellent | ~75 μm | Clear, consistent dye uptake across full color range | Best all-around CNC alloy for anodizing. KUSLA Prototype’s default recommendation. |
| 6063-T5 | 6xxx (Mg+Si) | Excellent | ~100 μm | Brightest clear finish; best for chemical brightening | Preferred for architectural and consumer cosmetic finishes. Low iron needed for bright finish. |
| 7075-T6 | 7xxx (Zn) | Good | ~100 μm | Shifts brown/bronze; difficult to color-match with 6xxx parts | Strong CNC alloy, but zinc content causes brownish tint. Avoid mixing on same anodizing rack as 6xxx. |
| 5052-H32 | 5xxx (Mg) | Good | ~90 μm | Slight gray tone; acceptable for most colors | Common sheet metal alloy. Watch for oxide streak patterns. |
| 2024-T3 | 2xxx (Cu) | Poor | ~38 μm | Yellow-gray; very limited dye absorption | High copper (>4%) disrupts oxide formation. Needs pulse rectification and low-temp bath. Avoid for cosmetic parts. |
| ADC12 / A380 | Cast (Si+Cu) | Poor | ~13 μm | Dark, mottled, non-uniform | High silicon die-cast alloy. Anodizing produces heavy black smut. Generally not recommended. |
Max thickness values per MIL-A-8625F Type III. Actual limits vary by anodizer capability and part geometry.
The practical rule for color matching across a multi-part assembly: use the same alloy for all anodized components. Mixing 6061 and 7075 on the same assembly and requesting matching black anodize produces two visibly different blacks — one neutral, one bronze-shifted. KUSLA Prototype flags this mismatch during DFM review and recommends either unifying the alloy or specifying separate color tolerances for each material. For detailed machining parameters by alloy, see the surface finish Ra chart — the pre-anodize surface finish directly affects the final appearance.
Machine for the Coating You Have Not Applied Yet
Because anodizing grows the surface outward, every toleranced dimension changes after finishing. The dimensional growth is deterministic — it depends on the anodizing type and the specified coating thickness — which means the CNC programmer can compensate for it by machining the part slightly undersized before it goes to the anodizer. The challenge is knowing exactly how much to compensate.
The growth ratio
Type II sulfuric anodize grows roughly one-third of the total coating thickness outward from the original machined surface. A 20 μm Type II coating adds approximately 6.7 μm per side to external dimensions and removes approximately 6.7 μm per side from internal dimensions (bores get smaller). Type III hard anodize grows roughly half the coating thickness outward. A 50 μm Type III coating adds approximately 25 μm per side.
External dimension (shaft, OD):
Machine to = Finished dim − (Thickness × Growth ratio × 2)
Internal dimension (bore, ID):
Machine to = Finished dim + (Thickness × Growth ratio × 2)
Worked Example: Type III, 50 μm coating on a ∅25.00 mm bore
Growth ratio (Type III) = 0.50
Per-side buildup = 50 × 0.50 = 25 μm = 0.025 mm
Total bore shrinkage = 0.025 × 2 = 0.050 mm
Machine bore to: 25.00 + 0.050 = 25.050 mm
Worked Example: Type II, 20 μm coating on a ∅10.00 mm shaft
Growth ratio (Type II) = 0.33
Per-side buildup = 20 × 0.33 = 6.6 μm ≈ 0.007 mm
Total shaft growth = 0.007 × 2 = 0.014 mm
Machine shaft to: 10.00 − 0.014 = 9.986 mm
The alkaline etch step before anodizing also removes base metal — typically 2.5 to 10 μm, depending on etch time and concentration. For precision parts with tolerances tighter than ±0.025 mm, KUSLA Prototype specifies “light etch” or “no-etch” on the work order and communicates the etch allowance to the anodizer explicitly. The CNC machining tolerances guide covers how to specify tolerances that account for both machining and post-processing dimensional changes.
Need CNC Parts Machined and Anodized to Spec?
KUSLA Prototype machines and coordinates anodizing in-house. Upload your drawing and get a quote that includes dimensional compensation, alloy verification, and MIL-A-8625F compliance — no separate finishing vendor to manage.
Get a Quote with AnodizingHow to Specify Anodizing on an Engineering Drawing
A drawing note that says only “anodize” or “anodize per MIL-A-8625” leaves the anodizing type, class, thickness, and color unspecified. The finishing shop either queries the drawing (adding days) or makes assumptions (adding risk). The correct format per MIL-A-8625F includes five elements: type, class, color, thickness, and sealing requirement.
Callout format
The standard structure is: “Anodize per MIL-A-8625F, Type [I/II/III], Class [1/2], [color or undyed], [thickness range], [seal type]”
Three worked examples
Aerospace bracket, Type I, undyed:
“Anodize per MIL-A-8625F, Type IB, Class 1, undyed, 2.5–5.0 μm, hot water seal. Critical surfaces per detail A.”
Consumer electronics enclosure, Type II, black:
“Anodize per MIL-A-8625F, Type II, Class 2, black per [color chip reference], 15–20 μm, nickel acetate seal. Cosmetic surface per detail B — no handling marks, no rack marks on visible faces.”
Hydraulic valve body, Type III, natural:
“Anodize per MIL-A-8625F, Type III, Class 1, natural (dark gray acceptable), 50–65 μm. Bore diameters A, B, C to be masked — do not anodize. All other surfaces anodized.”
Three common specification mistakes KUSLA Prototype flags during DFM review: omitting the class (which leaves dye/no-dye ambiguous), specifying Type III on a 2024 alloy without confirming the anodizer can handle the copper content, and failing to call out masking on threaded holes or press-fit bores where the dimensional buildup would cause interference. For a broader look at how anodizing compares with powder coating, see the dedicated comparison guide.
Picking the Right Anodizing Type: A Decision Framework
Most engineers default to Type II because it works, it is affordable, and it comes in every color. That default is correct roughly 70% of the time. The remaining 30% splits between applications that genuinely need Type III’s hardness and a small fraction still locked into Type I by legacy aerospace specifications. The decision framework below starts with the functional requirement and arrives at the type.
Fig. 2 — Decision flowchart for anodizing type selection. Start with the primary functional requirement; edge cases and industry norms narrow the choice further.
For parts that need both wear resistance and vibrant color, the options are limited. Type III accepts black dye reliably; other dark colors (dark blue, dark red) are possible but alloy-dependent and harder to control batch-to-batch. If the design absolutely requires both high hardness and a specific bright color, KUSLA Prototype recommends considering alternative finishes such as hard chrome plating or PVD coating instead of forcing Type III into a role it was not designed for.
When Anodizing Goes Wrong: Six Failure Modes and How to Prevent Them
Anodizing failures are almost always traceable to one of six root causes. Most of them are preventable at the design or specification stage — before the part ever reaches the anodizing tank. KUSLA Prototype’s DFM review catches the most common issues; the table below covers the full set.
| Failure Mode | Symptom | Root Cause | Prevention |
|---|---|---|---|
| Burning / dissolution | Dark spots, pitting, or powdery surface on the anodized part | High-copper alloy (2xxx series) at standard bath parameters; current density too high for the alloy | Use pulse rectification for 2024/2011. Communicate alloy to anodizer. Avoid 2xxx for Type III >38 μm. |
| Color mismatch | Visibly different color between parts in the same batch, or batch-to-batch variation | Mixed alloys on the same rack; different material lots with varying Mg/Si/Fe ratios; inconsistent etch time | Rack same-alloy parts together. Specify L*a*b* color window on drawing. Use single material lot for cosmetic assemblies. |
| Thermal crazing | Fine network of micro-cracks on Type III coating, visible after thermal cycling or at operating temperatures >80 °C | Differential thermal expansion between dense Type III oxide and aluminum substrate | Limit Type III operating temperature to 80 °C. Use thinner coating (25–40 μm) for parts that see thermal cycling. Consider Type II if wear is moderate. |
| Acid entrapment | White residue weeping from blind holes, recesses, or complex internal geometry after sealing | Sulfuric acid trapped in cavities that cannot be fully rinsed; residual acid continues to attack the coating | Design drainage paths (minimum ∅3 mm vent holes) for blind cavities. Specify extended rinse cycles. Avoid blind holes deeper than 4× diameter on Type III parts. |
| Soft spots / uneven coating | Areas of thin or missing oxide; parts fail hardness or thickness test locally | Contamination (oil, machining residue) not fully removed in pre-treatment; poor electrical contact at rack points | Degrease and clean parts thoroughly before shipping to anodizer. Specify cleaning verification. Mark preferred rack contact points on drawing. |
| Dimensional interference | Press-fit bores too tight; threaded holes won’t accept fasteners; mating surfaces bind | No dimensional compensation for coating buildup; critical features not masked | Apply growth-ratio compensation per Section 4. Mask press-fit bores, threads, and datum surfaces. Specify masking on drawing with detail callouts. |